http://www.justanswer.com/gmc/5vwnt-gmc-... Go to Condition B.. If all that doesnt fix it then you must have broken wires or bad grounds Was this answer helpful? If your bad side (left/right) is now blinking (the wand action will be reversed), the problem most likely a bad column switch. Source
If, for some reason, they work fine, then you have some other issue. Any suggestions would be appreciated. 4 out of 4 people think this is helpful. permalinkembedsavegive gold[–]soopanoob 0 points1 point2 points 2 years ago*(0 children)I have left reddit for Voat due to years of admin mismanagement and preferential treatment for certain subreddits and users holding certain political and The connectors were not gripping the relay terminals properly.
Clip the test light to a chassis ground first like some chrome trim. Any advice or insight would be greatly appreciated! 6 commentsshareall 6 commentssorted by: besttopnewcontroversialoldrandomq&alive (beta)[–]cptboring 0 points1 point2 points 2 years ago(3 children)BCM fuse 9 is listed as "STOP LP 10A" in the diagram September 13 by Richard Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Rear Brake Lights/Turn Signal Lights Problem This is a discussion on Rear Brake Lights/Turn Signal Lights Problem within the Automotive Support forums, part of the Tech Support Forum category.
Yes No Sorry, something has gone wrong. Cancel The All-New Pro Tech Toolkit The high performance electronics repair kit. It's an easy fix, under 30 minutes, parts are reasonable. No Brake Lights Or Turn Signals On Trailer So if things get just too wierd - ck your grounds!
Push the wires into the back of the light housing. Both wires are hot (+). I tried changing the bulb, and my husband checked the fuses and said they all seemed to be fine.... You may need to scroll down to multiple comment pages if you have commented a lot.
Thanks again for the help! 07-08-2010, 10:17 AM #8 pspeir Registered Member Join Date: Jul 2010 Posts: 29 OS: Windows 7 Okay, got the tester and took out My Brake Lights And Blinkers Dont Work The only thing still out is the in-dash passenger side indicator light. I did notice when my blinker is on (headlights turned off)when I hit my break my dash lights for my "heat and cool" flash with my blinker. CONDITION D: No brake or signal on either side.
January 15 by jayeff I still haven't figured it out so I'm just going to take it to a shop I know it has to be something simple cause I don't Can I ask do several people drive the car and change the position of the tilt steering? Brake Light And Turn Signal Not Working On One Side Brake lights were working intermittently. Turn Signal And Brake Light Not Working On Trailer checked current through to rear .
No signal lights on either side, but you've got brake lights on one or both sides. this contact form I have brake lights and turn signals when I pulled my "tail light/ courtesy marker light" fuse But when I put the fuse back in I have no turn signals and Cancel Ralph Beesley Rep: 1 Posted: April 18 Options Permalink History Are the bulbs good or blown. Any clue what might fix this problem? Brake Lights And Turn Signals Not Working F150
If you have power going to the turn signal switch but none coming out of the turn signal switch. Any advice you receive you must use AT YOUR OWN RISK. Solder and shrink tube the new wire to these pigtails and give it a test. have a peek here If that isn't available, provide all you know and explain why.
Their is no adjustment I'm aware of on 98 GMC Sierra z71. Brake Lights Dont Work But Turn Signals Do We use data about you for a number of purposes explained in the links below. I hate to spend the $300 to buy a new LCM without knowing that's the problem.
Go to Condition C. Test the connections to the rear as described below. After you create your account, you'll be able to customize options and access all our 15,000 new posts/day with fewer ads. Brake Lights And Hazards Not Working View the answer I have this problem too Subscribed to new answers Is this a good question?
But driver side turn sig DID work. If the connection to the rear is OK: Switch the #8 yellow and #8 green wire where they connect to the fuses underneath the steering column. However, If we turn off the lights the rear brake lamps won't light up when brake pedal is applied. http://pagesetter.net/brake-light/brake-light-not-working-but-tail-light-works.html If you didn't get an answer the first time, or you don't like the answer you got that does not mean you post it again. 2b) Updates are allowed, provided it
Some others don't consistently indicate flashing on the dashboard, or may not flash at all. on) and measure the voltage or use a test light on the pink wire. Some tests require a test light or a Volt/Ohm meter (VOM), but you may not need one initially. bulbs have been checked and are good.
Underhood fuse 69 is in the parking lamp/turn signal diagram. All posts without this information may be subject to being deleted. 3b) Any off topic posts must be flagged [Meta], [N/A], or similar. 4) Spam/Self-Promotion/Improper Linking. This is not a review forum for specific shops. If either of those conditions are not met, the switch is defective.
If nothing is working, check the brake switch and the turn signal switch. Check the front signal lights. (Sometimes the a bad front light will prevent the rear from working.) If the signal switch works, replace the signal(trailer) relay. Sharing personal information, or specifics on /r/MechanicAdvice is not allowed. Thought I had done a thourough job but still no change.
Push on the brake pedal (Ign. We're here to help so being rude won't get you very far. The signals are fused by the 4th fuse down (passenger's side) on the firewall. When the key is on they stop working.
just did mine and it was a pain but it solved the problem instantly.