Home > Not Working > Land Rover Discovery Electric Window Problems

Land Rover Discovery Electric Window Problems

Contents

If no power and the wire circut is good I am just going to make a splice repair as referenced above. Human Verification In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in Its interesting to know that the Range Rover Classic shares the same window lift ECU as the Discovery 1. Reply With Quote 02-09-2012,03:50 PM #10 TomOwen View Profile View Forum Posts Private Message View Articles 4WD Easy Member Join Date Jan 2010 Location SF Peninsula Posts 40 Harness clip can Source

so I could not see what was on the link NeoMobi is offline Quote Quick Reply Remove Advertisements Sponsored Links Land Rovers Only Forum Advertisement Reply Land Rover Note that passwords are case-sensitive. I have a cigar lighter plug with a 6' two conductor wire on it that I've connected two spade connectors to which I plug in to the switch connector on the Thanks!

Land Rover Discovery Electric Window Problems

I've checked and replaced the fuse but still nothing. Alexander Wayne 215 views 0:44 Discovery Window Regulator - Duration: 9:51. My 1995 RR Classic is a LHD. Forum FAQ Calendar Forum Actions Mark Forums Read Quick Links View Site Leaders Advanced Search Forum Land Rover Repair Forums Land Rover Repair Technical Boards Discovery Series I Repairing the Window

I repaired my own ECU by fixing the circuit board. There are several articles out there on how to repair the Window Lift ECU but none with how it was actually done....until now. Jumper wires worked for this, but may not be universal for all circuits that need repair. Discovery 4 Commercial Rear Windows If you are not seeing 12V on pin 4, then you probably have a failure in the ECU on the solder joint highlighted in the article.

first is the inhibitor switch pressed in? Range Rover Windows Not Working Land Rover Repair Forums Land Rover Repair General Member Introductions General Discussion Bicycle Forum "Funrover" Stage Accessories & Modifications Metal Fabrication Electronics Protection Recovery Gear Suspension Wheels & Tires Drivetrain Engine Will let you know how it goes. if none of the switches make them work, then it's the window ECU.

C288 has heavier gauge wires and is used to deliver power to the window circuits. 1. Range Rover Classic Window Ecu Have a look: http://www.roverparts.com/Parts/AMR1282RK.cfm #7 03-05-2011, 10:31 PM groundandpound Senior Member Join Date: Dec 2010 Location: Gaithersburg MD Posts: 316 Thanks: 0 Thanked 0 Times in 0 Posts Take the rover out for a spin and enjoy the cool breezes with the windows down!! '99 Land Rover Discovery 1 SD 2" RTE Springs +2" Terrafirma Shocks Terrafirma Turret Rings No i dont have a RAVE CD just the manual.

  1. The fronts on this newly acquired SE7 (less than a week) work fine but neither rear window does anything, no up/down/sounds/clicks/motion/anything etc, suggesting an electrical issue somewhere common to a harness
  2. Cheers #9 (permalink) 1st May 2010, 10:02 AM p38arover Major Part of the Heart and Soul of AULRO Gold Subscriber Join Date: Jan 1970 Location: Western Sydney Posts:
  3. Haynes does not show a location or reference removal/replacement.
  4. Watch Queue Queue __count__/__total__ Find out whyClose Land Rover Window ECU Repair Alexander Wayne SubscribeSubscribedUnsubscribe108108 Loading...

Range Rover Windows Not Working

Thanks again (You must log in or sign up to reply here.) Show Ignored Content Page 1 of 2 1 2 Next > Share This Page Tweet Your name or Anybody had similar problems? Land Rover Discovery Electric Window Problems Tim the Enchanter is offline Quote Quick Reply post #12 of 14 (permalink) Old 08-31-2010, 01:34 PM Crusty Rover Member Join Date: Aug 2010 Posts: 1 Mentioned: 0 Post(s) Land Rover Discovery Window Regulator Sorry if this is the same site that is refrenced above, for some reason dweb is not working for me right now.

There is at least one solder joint that is usually bad and this is common to the DI's. this contact form It also shares the same grounding point as front window switches that work. Thanks a lot everyone for your inputs. The last pic you posted shows the ECU plugs, the top left wire on the lower plug feeds the rear window switches (white/pink). Discovery 2 Drivers Window Not Working

Some people have reported that they have a faulty or "Cold" solder issue. Checked Isolation switch and its leads: works correctly. I may just press-fit-and-pray or wrap a zip tie around it to keep it in place but I could not get it out any other way. http://pagesetter.net/not-working/resize-chrome-window-javascript.html Next, re-install the glove box by sliding the two retaining springs back through the slots and then tightening up the 4 7-mm bolts.

Register Help Remember Me? Land Rover Discovery 1 Electric Windows careful prodding with the multimeter proved a bad connection. Could there be anything else wrong?

I think that'll help me narrow it down.

May 6, 2007 at 7:50 PM #8 Zende Full Access Member Posts: 51 Likes Received: 0 Joined: Oct 13, 2006 Where is the BCU located and what may I do to After you get the finisher removed, it's time to remove the glove box. A garage changed the fuse and it was ok for a couple of days and then again they went dead again. Land Rover Discovery 2 Front Window Not Working Reply With Quote 08-28-2011,09:09 PM #4 SloHybrid View Profile View Forum Posts Private Message View Articles 4WD Extreme Member Join Date Jun 2007 Location Atascadero, CA Posts 1,793 It's the ECU

Page 1 of 2 1 2 Next > Jul 5, 2006 at 6:17 AM #1 zunni Guest Hi, I have a great '99 Discovery II and it has been working great Mr1superdean1 1,766,599 views 3:52 3 Amigos diagnostic repair on wheel sensor Discovery 2 using Lynx Britpart interface unit - Duration: 6:10. Gently remove the harnesses and re-install the ECU. Check This Out Im having the same problem.

You need to be careful not to overheat the circuit you're soldering on. I use this to actually complete the connection so that if it sparks there's no chance of messing up the contacts in the connector (preventing reinstallation of the switch later). You need to run the jumper to the white/pink wire that goes to the harness, not the 1" left on the plug. My '$1500 special' gets better by the day.....

That will run the motor. There are 4 plastic fasteners holding this on (you can use a flat head screwdriver to pop them out if you don't have a panel pulling tool). HOWEVER: the retaining clip on the upper connector (that which requires Squeezing) can be a bear to undo. Once the ECU is back in it's home, replace the plastic piece you pried off earlier and reconnect the harness (Note: there are two channels in the plastic housing that the

QUESTION: Anyone have any trouble shooting tips on this or know of anything "quirky" about or attached into the rear window system? Repair it and put it back together. But those are the colors at the switch connector. Were the front windows working and then just suddenly stopped, or did they fail at different times.

I can send it over on Monday if need be, good luck, PM me if you want #6 03-05-2011, 10:22 PM blackcloud Junior Member Join Date: Jan 2011