Home > Not Working > Trailer Lights Not Working Properly

Trailer Lights Not Working Properly

Contents

Reply With Quote 04-30-2011,02:20 PM #3 Xrunner View Profile View Forum Posts Private Message Join Date Dec 2010 Location Columbia river Posts 285 +11 Originally Posted by K447 I would think I then redid the ground on the truck's converter box, and then my light testing of the truck's plug was consistent with what I saw on the trailer - nothing from This should cause your test light to illuminate. Originally posted by 2 Eagles View Post I would say that your connector on the truck side is bad on the yellow wire. http://pagesetter.net/not-working/trailer-lights-don-39-t-work.html

Also be mindful of the orientation of the plug when matching each pin to its function. Rating is available when the video has been rented. Most people give up and just get their speech ready for when and if they do get stopped by law enforcement. If that all looks good and your trailer lamps use old-school bulbs, check for corrosion, looseness or damage in the bulb socket.

Trailer Lights Not Working Properly

water INSIDE the bulb itself! You probably have a break in that wire somewhere from the connector to the light bulb. Assistant: You will need to view and assist the trailer while performing portions of the test. Now do these tests again with the headlights turned on.

It requires you to remove the tail lamps, unplug the electrical plugs for the lamps, install a jumper connection on each side of the car, and then run the harness behind Optional: If Your Trailer has Electric Brakes Touch the test light to the “Electric Brakes” pin. The test light should start out dim and get brighter as the outgoing power from the brake controller increases. Left Running Light On Trailer Not Working Do you have a trailer troubleshooting, repair or maintenance question - submit it here.

Check the ground or white wire connection to each lamp. Right Turn Signal On Trailer Not Working Work your way along the wire, testing until you get voltage, which will tell you where the break is. By jasonbedell in forum Kawasaki PWC Performance (4-stroke) Replies: 7 Last Post: 07-23-2007, 08:52 PM Trailer Lights By pauladave in forum Yamaha Open Discussion Replies: 10 Last Post: 03-21-2007, 03:32 PM Loading...

See how it goes off? Trailer Brake Lights Dont Work Your volt/ohmmeter will test these connections. 2. Obviously, the opposite kind of jack will be used on the boat trailer with three male pins and one female pin acting as the ground (see photo). What type of truck?

Right Turn Signal On Trailer Not Working

Try cleaning it. When it comes to wiring i am completely lost. Trailer Lights Not Working Properly etrailer.com 262,578 views 4:18 Installing a Trailer Wiring Package : How to Connect the White Ground Wire of a Trailer Wiring Package - Duration: 2:44. Trailer Running Lights Not Working One Side J John Nashville, TN Shop By Vehicle Car Wagon SUV/Jeep Minivan Truck RV/Camper Shop Popular Brands Order Information Order Tracking Shipping Information Lowest Price Pledge Privacy Policy Your Account Login Customer

Touch the test light to the “Running Lights”. http://pagesetter.net/not-working/thermostat-not-working-properly.html When holding the plug, the rectangular “bump” should be at the top. Next move to the lights themselves. anyone get their GP1800 yet? Left Side Trailer Lights Don't Work

And don't forget to check the ground at the last fixture... Did you ever have it where all the lighting worked properly? Have an assistant also press the brake pedal. navigate here Hey, you'd be surprised, a lot of people read this section Last edited by K447; 05-08-2011 at 09:49 PM.

Also, depending on the truck, you may have a fuse for both sides. 1998 Wellcraft Eclipse 24 Cuddy Volvo Penta Duo-Prop 7.4L "LK" 2006 Sun Tracker Party Barge 21 Mercury 90 One Trailer Brake Light Not Working Refer to manufacturerinstallation instructions and specs for complete information.The first thing you want to do when you first start working on electrical problems is you want to divide and conquer. Loading...

The four-prong flat fittings between trailer and tow vehicle were a match.

Now retest the problem. I attached it to another trailer and it still had the left side problems. Trailer light wiring is often exposed and subject to harsh conditions. Trailer Brake Lights And Turn Signals Not Working We will show you how to check both.

ok. ... Dont even know where to start. I've spent a lot of time to get this far. his comment is here Tags: None Seon Petty Officer 1st Class Join Date: Apr 2008 Posts: 297 #2 April 12th, 2011, 01:54 PM Re: left turn signal and brake light not working on trailer Check

Trending Now Veterans Day Leon Russell Scarlett Johansson Demi Lovato Natalie Portman 2016 Crossovers Dwyane Wade Miranda Lambert Auto Insurance Quotes Dating Sites Answers Relevance Rating Newest Oldest Best Answer: Short DC can be indicated by a dashed line (AC is wavy). You want to verify which one actually has the problem. Hahaa!

Just a little Basic Electricity before we move on: your trailer lights are powered by 12 volt Direct Current electricity. It is helpful to use corresponding colors for the test leads, as shown. If you have voltage at the halfway mark, you know the fault is between there and the fixture. The make a boat trailer that cant handle going into the water?

Reply With Quote Quick Navigation Around The Farm Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums Announcements Events Missing Horses Discussion Forums Dressage Hunter/Jumper Eventing My Van is a 2000 year model. i had never used the plug on this truck so i wanted to make sure it was in working order. Start at a point along the wire, midway from fixture to the trailer's connector and test again, using the black probe on the trailer frame and the red probe on the

It may also blink if your brake controller has a test function. What do I clean the inside of the block with? A light fixture may use the metal part of the frame to serve as the ground, or a more common (and better) way is to run a separate ground wire to The lights are even coming on!